<menu id="myki2"></menu>
<nav id="myki2"></nav>
  • <nav id="myki2"></nav>
    <nav id="myki2"><optgroup id="myki2"></optgroup></nav>
  • 網站公告:

    新聞中心

    濟南精拓流體設備有限公司

    電話:0531-69951198

    郵箱:jingtuolt@163.com

    傳真:0531-69951198

    地址:濟南市歷城區西周南路9號

    網址:http://www.massonisweb.com

    企業動態

    當前位置:首頁 - 新聞中心 - 企業動態 - 使用企業增壓缸我們應該注

    使用企業增壓缸我們應該注意什么?

    發布時間:2020-10-29 16:47:36   發布人:http://www.massonisweb.com
    1、保持清潔
    1. Keep clean
    在將增壓缸接入氣路前,敬請先將管路及元件內的灰塵等雜物清除,以免降低增壓缸的使用壽命。
    Before connecting the booster cylinder to the air circuit, please remove the dust and other impurities in the pipeline and components, so as to avoid reducing the service life of the booster cylinder.
    2、正常氣壓范圍內使用
    2. Use within normal pressure range
    缸在正常使用時工作氣壓必須要按照檢驗報告中規定的工作氣壓范圍內工作,不得超過規定的工作壓力.。
    When the cylinder is in normal use, the working pressure must be within the working pressure range specified in the inspection report, and shall not exceed the specified working pressure.
    3、注意增壓缸的工作環境
    3. Pay attention to the working environment of booster cylinder
    缸在設工作環境內的溫度已定,若因工作需要變換工作環境超過溫度需與玖容增壓缸技術相關人員聯系處。
    The temperature in the working environment of the cylinder has been determined during the design. If the working environment exceeds the temperature due to working needs, contact the technical personnel of the nine volume booster cylinder.
    由于缸中的部分元件為鐵質,所以請不要將其置于工況環境特為復雜的環境內使用(如有化學物質的接觸環境),另請在缸前端加裝有效的空氣處理元件(三點組合)并接時加油潤滑及排水處理。
    As some components in the cylinder are made of iron, please do not use them in the environment with complicated working conditions (such as chemical contact environment). In addition, please install effective air treatment elements (three-point combination) at the front end of the cylinder, and then add lubrication and drainage treatment.
    4、不可擅改加其它液壓油
    4. Do not add other hydraulic oil without authorization
    增壓缸在設所選用的液壓油價質為VG68#抗磨液壓油,不可撤擅自改用其它液體介質(如機油.水等)。
    The quality of VG68 anti-wear hydraulic oil is selected in the design of booster cylinder, and it is not allowed to use other liquid medium (such as engine oil, water, etc.) without authorization.
    5、一定要按程序操作
    5. Be sure to follow the procedure
    動作程序一定要按照氣路配裝圖的動作程序工作即預壓動作-增壓動作增壓釋壓-預壓復位
    The operation procedure must be in accordance with the operation procedure in the gas circuit assembly drawing, that is, pre pressure action - pressure increase action - pressure release - pre pressure reset
    6、注意保養,經常檢查增壓缸運轉
    6. Pay attention to maintenance and check the operation of booster cylinder frequently
    為避免缸在增壓時動作的壓力過大破壞您的模具或工件,敬請在增壓段進入口處加裝一減壓閥,以便能有效保護您的產品。
    In order to avoid damage to your mold or workpiece due to excessive pressure during cylinder pressurization, please install a pressure reducing valve at the inlet of pressurization section, so as to effectively protect your products.
    氣液增壓泵
    為確保增壓缸工作的穩定性,建議盡可能在三聯件與增壓缸之間并聯加裝一儲氣筒。
    In order to ensure the working stability of the booster cylinder, it is suggested to install an air reservoir in parallel between the triplet and the booster cylinder as far as possible.
    使用增壓缸500000次以上或半年以上時,建議將缸中的液壓油全部更換一次,以提高缸的使用壽命和工作年限。
    When the booster cylinder is used more than 500000 times or more than half a year, it is recommended to replace all the hydraulic oil in the cylinder once, so as to improve the service life and working life of the cylinder. 

    13188935873

    qq

    甘肃11选5