<menu id="myki2"></menu>
<nav id="myki2"></nav>
  • <nav id="myki2"></nav>
    <nav id="myki2"><optgroup id="myki2"></optgroup></nav>
  • 網站公告:

    新聞中心

    濟南精拓流體設備有限公司

    電話:0531-69951198

    郵箱:jingtuolt@163.com

    傳真:0531-69951198

    地址:濟南市歷城區西周南路9號

    網址:http://www.massonisweb.com

    常見問題

    當前位置:首頁 - 新聞中心 - 常見問題 - 氣液增壓器與氣液增壓泵有

    氣液增壓器與氣液增壓泵有哪些區別?

    發布時間:2020-10-27 15:57:00   發布人:http://www.massonisweb.com
    氣液增壓器與氣液增壓泵,原理都是大活塞推動小活塞,由于面積差,使液體壓力放大,F=但兩個的本質區別在于,氣液增器一般為單個往復運動,不連續運動,進出口沒有單向閥,外掛油杯,一般用壓力脈沖,沖壓等場合;氣液增壓泵能依靠自身的換向閥,接通壓縮空氣連續往復運動,進出口裝有單向閥,出液連續,一般用于壓力檢測。
    The principle of gas-liquid supercharger and gas-liquid booster pump is that the large piston pushes the small piston, which enlarges the liquid pressure due to the area difference, f = but the essential difference between the two is that the gas-liquid booster is generally a single reciprocating motion, discontinuous movement, there is no one-way valve at the inlet and outlet, the external oil cup is generally used for pressure pulse, stamping and other occasions; the gas-liquid booster pump can be connected by its own directional valve Compressed air continuous reciprocating movement, inlet and outlet equipped with one-way valve, liquid continuous, commonly used for pressure detection.
    氣體增壓泵利用大面積活塞端的低壓氣體驅動而產生小面積活塞端的高壓流體。可用于壓縮空氣及其它氣體,輸出氣壓可通過驅動氣壓無級調節。輸出流量大:只需0.3-0.8MPa壓縮空氣驅動就可獲得較大的輸出流量工作時,迅速往復工作,隨著輸出壓力接近設定壓力值時泵的往復運動速度減慢直至停止。并保持這個壓力,此時消耗能量很小,無熱氣體增壓泵量產生,無零件運動。當壓力平衡打破后,氣動增壓泵自動開始工作到下一個平衡。
    The gas booster pump uses the low pressure gas of large area piston end to drive and produce high pressure fluid of small area piston end. It can be used for compressed air and other gases. The output pressure can be adjusted steplessly by driving air pressure. Large output flow: only 0.3-0.8mpa compressed air drive can obtain large output flow. When working, it can quickly reciprocate. When the output pressure is close to the set pressure value, the reciprocating speed of the pump slows down until it stops. And maintain this pressure, at this time the consumption of energy is very small, no hot gas booster pump generated, no parts movement. When the pressure balance is broken, the pneumatic booster pump automatically starts to work to the next balance.
    氣液增壓泵
    材質優良高壓部分材質為不銹鋼。高壓柱塞材質為不銹鋼,并采用雙層密封。維護簡單氣動增壓泵的零件及密封少,維護簡單且成本低。相同系列泵的所有"O"型圈,維修包易損部件可相互替換,大大降低了維修成本。氣動增壓泵出廠前已加注潤滑劑,工作時無需外部潤滑。
    The high pressure part is made of stainless steel. The high pressure plunger is made of stainless steel with double seal. Simple maintenance, less parts and seals of pneumatic booster pump, simple maintenance and low cost. All the "O" rings of the same series of pumps and the vulnerable parts of the repair kit can be replaced with each other, greatly reducing the maintenance cost. The pneumatic booster pump has been filled with lubricant before delivery, so external lubrication is not required during operation.
    只有把上述所講的內容設定好,我們的操作才算完成,如果您這邊在后續的過程中有任何的問題,歡迎致電或者是在網站上邊留言:氣液增壓泵http://www.massonisweb.com
    If you have any problems in the follow-up process, please call or leave a message on the website: gas-liquid booster pump http://www.massonisweb.com

    13188935873

    qq

    甘肃11选5